DHEC
End cap for the terminations of a pre‑insulated pipeline: a shrink component that closes the casing end and keeps water out of the insulation where the line ends or breaks. Used at line terminations, transitions, and where pre‑insulated pipe meets uninsulated pipe.
The termination
The drawing is Kampek's own. It asserts only what is already published on this site or on the manufacturer's own pages.
- 1PE casing
- 2PUR insulation
- 3DHEC end cap, casing down to carrier pipe
- 4The cap seals down onto the carrier pipe
- 5Carrier pipe continues uninsulated
Sizes and order codes
These come from Kampek's own product catalogue. Take the code from the row and request a quote with it, so nobody has to retype it. Availability is confirmed with the quote.
DHEC end cap
The size number is the catalogue's own series number, not a millimetre dimension. The source does not say what it measures.
| Size | Code |
|---|---|
| 2000 | DHEC-2000(C30) |
| 2060 | DHEC-2060(C30) |
| 2100 | DHEC-2100(C30) |
| 2200 | DHEC-2200(C30) |
| 2300 | DHEC-2300(C30) |
| 2340 | DHEC-2340(C30) |
| 2400 | DHEC-2400(C35) |
| 2500 | DHEC-2500(C30) |
| 2600 | DHEC-2600(C20) |
| 2630 | DHEC-2630(C30) |
| 2700 | DHEC-2700(C30)) |
| 2800 | DHEC-2800(C20) |
| 2900 | DHEC-2900(C20) |
| 3000 | DHEC-3000(C15) |
| 3200 | DHEC-3200(C20) |
| 3250 | DHEC-3250(C20) |
| 3250-P604 | DHEC-3250-P604(C20) |
| 3280 | DHEC-3280(C20) |
| 3300 | DHEC-3300(C20) |
| 3350-01 | DHEC-3350-01(C20) |
| 3350-02 | DHEC-3350-02(C20) |
| 3350-03 | DHEC-3350-03(C18) |
| 3360-01 | DHEC-3360-01(C22) |
Technical data
23 codes in Kampek's catalogue
Pick a code and it carries straight into the quote request. Availability is confirmed with the quote.
Other products in this family
Wrap‑around heat‑shrink sleeve for sealing the joint casings of pre‑insulated district heating pipes.
Closure patch for Covalence wrap‑around heat‑shrink sleeves.
Heat‑applied closure patch that seals the foam‑injection hole in a pre‑insulated pipe casing after PUR foaming, keeping water out of the insulation.
Heat‑melted PE copolymer stick for repairing small surface scratches in a PE coating where the damage does not reach the steel.
Zippered, fibre‑glass reinforced end cap for the ends of pre‑insulated pipe.
Adhesive sealing tape on a roll with a release liner.
Tubular heat‑shrinkable sleeve for corrosion protection of welded pipe joints in distribution lines.
Thick‑wall tubular heat‑shrinkable sleeve whose high shrink ratio covers irregular shapes.
Tubular heat‑shrinkable sleeve for corrosion protection of socket joints.
Wrap‑around heat‑shrink sleeve for the girth welds of steel pipe in distribution and transmission systems.
Wrap‑around heat‑shrink sleeve for the girth welds of steel pipe in distribution and transmission systems, the same family as WPC‑C30 and also available in a narrower 285 mm width.
Alongside the standard range runs a set of specialty products that are asked for less often but have their own place.
Wrap‑around heat‑shrink sleeve for the girth welds of steel pipe on gas and other transmission lines.
Fibre‑glass reinforced wrap‑around heat‑shrink sleeve for horizontal directional drilling.
Solvent‑free two‑component epoxy primer for Covalence three‑layer systems (HTLP60‑DCS, HTLP80, DIRAX) on steel pipe girth welds.
Stretchable, hand‑wrapped heat‑shrink tape for corrosion protection of pipe bends and small‑diameter straight pipe in distribution networks.
High‑viscosity sealant‑based mastic tape used to fill damaged coating before a repair patch or sleeve goes on, restoring the original coating thickness.
Request a quote: DHEC
Tell us quantity and schedule; we reply on availability and terms within days.